Twitxy Saved

Quilter

Verified account This account is verified. Learn more

@quilterai

Quilter is enterprise-grade, physics-driven AI that automates printed circuit board layout design.
Los Angeles quilter.ai Joined September 2023
90 Following 1.6K Followers 231 Posts

Latest posts 5

Pinned post

Quilter Verified account @quilterai
How does an AI-designed PCB compare on EMI with the chip vendor's own reference design? Drum roll, please, again!

A year ago, we manufactured our Project Speedrun, the first computer designed by AI. Quilter's physics-driven AI placed and routed both boards of an NXP i.MX 8M Mini Linux system, and engineers spent 38.5 hours on cleanup.

EMI was the first question people asked about Speedrun and the most common criticism. We're glad to answer it now with third-party measurements.

None other then Kenneth Wyatt, the EMC Doctor, measured Project Speedrun against a board built from NXP's i.MX 8M Mini reference design files, in a TEM cell in his lab.

✅ Through much of 250 to 650 MHz, the Speedrun trace sat below the NXP-design trace, with a gap of about 12 dB in part of that range by Ken's estimate
✅ Broadband DC-DC converter noise from 10 to 250 MHz was about 5 dB lower
✅ The likely Ethernet clock harmonics were lower too, with the same Ethernet PHY on both boards

These are bench pre-compliance measurements at the TEM cell output, so they don't predict margins at a 3 m or 10 m test distance. The write-up covers the setup and the limits.

quilter.ai/blog/ai-design…
5 replies 7 reposts 53 likes 9.1K views View on X
Quilter Verified account @quilterai
We are observing a very interesting trend in the industry! After decades of losing ground to computer science, electrical engineering is gaining students again: in fall 2025, EE enrollment at four-year colleges rose 14% , while computer and information science fell 8.1%.

🔹 In 1980, U.S. colleges awarded about 1.2 EE bachelor's degrees per computer and information science degree. By 2022, about 0.15.
🔹 That decline is why we argued in April that the electrical engineer shortage is structural.
🔹 New students need years of hands-on experience before they can take the senior roles teams struggle to fill.
🔹 Meanwhile, demand keeps growing: EE job postings on Indeed are 55% above their February 2020 level.

Big thank you to Judy Warner and Dr Eric Bogatin for providing insights for this piece.

quilter.ai/blog/engineeri…
Quilter Verified account @quilterai
Does a signal's rise time increase as it travels through a cable?

Dr. Eric Bogatin measured a scope's probe compensation signal through coax:
• 6 ft: about 250 nsec
• 12 ft: about 600 nsec
• 18 ft: almost 1 µsec

He shows that loss, dispersion, cable capacitance, and time of flight don't explain it. What does?

Eric's explanation and two more puzzles: quilter.ai/blog/cable-len…
Quilter Verified account @quilterai
Can GPT-6 Astra route an 8-layer board with DDR memory? Drum roll, please! We had it drive @altium for 62 hours, with the autorouter off.

None of the public tests of @OpenAI's Astra have used it on even a moderately complex board. We ran this one on our Project Speedrun system-on-module.

✅ Closed 836 of 857 open connections, bringing the board to 98.1%
✅ Ran overnight without supervision and repaired a supply net a copper pour had split
❌ DDR timing failed, with 120 ps of within-pair skew against a 1 ps limit
❌ 1,555 track segments ran on ground layers where the rules prohibit routing
💲 API spend for the run was about $2,900.

The prompt, design files, and Astra's final report are on GitHub for anyone to check.

Astra did not produce a working board, and we do not think it is practical to use it for any professional work, but it was still impressive that a general-purpose model drove a professional EDA tool through its interface for close to three days, coordinated its own helper agents, and documented every change it made.

What do you think about Astra's performance?
1:05
14 replies 31 reposts 287 likes 31K views View on X
Quilter Verified account @quilterai
“So far, the best thing that people have created are these things called autorouters, which are notoriously hated.”

That’s our CEO @sergiynest on Inside the Silicon Mind with @FirasSozan, talking about 60 years of attempts to automate PCB layout. The conversation also covers his five years as a radiation effects engineer at @SpaceX and why he starts from physics and first principles when he takes on a hard problem.

Autorouters gave PCB layout automation such a bad rep that many engineers are allergic to automation attempts. Some designers won’t touch an autorouter. Others use it on fanouts, buses, or less critical nets and are content with the results.

Which camp are you in? And what would it take for you to trust a layout automation tool?
1:18